Provide Latest Cisco 350-040 pass4itsure PDF With All New Questions And Answer

Exam A QUESTION 1
In Cisco MDS, how is a pWWN assigned to a dynamically assigned iSCSI?
A. by the system
B. by the user in the configuration of the iSCSI target
C. by the iSCSI host
D. created with iSCSI host name, iSCSI driver, and Connection ID
E. by the storage system attached to Fibre Channel

Correct Answer: A QUESTION 2
Which of these TCP ports does iSNS use?
A. 3205
B. 3225
C. 3226
D. 3325

Correct Answer: A QUESTION 3
Is the iSNS client supported on VRRP interfaces?
A. yes
B. no
C. only when the storage_services_enabler_pkg license is enabled on the switch
D. only on Cisco IPS line cards

Correct Answer: B QUESTION 4
Can Cisco Fabric Services be used to distribute iSCSI initiator configurations?
A. yes
B. no
C. only when the SAN_EXTN_OVER_IP_18_4 license is installed on the switch
D. only when ENTERPRISE_PKG is installed on the switch

Correct Answer: A QUESTION 5
Which of these is used to identify the special characters used in Fibre Channel encoding?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 350-040
A. K28.5
B. 8B/10B
C. 3B/4B
D. D28.5
E. idle
Correct Answer: A QUESTION 6
Which three of these Fibre Channel words are known as primitive signals? (Choose three.)
A. NOS
B. R_RDY
C. CLS
D. LIP
E. IDLE

Correct Answer: BCE
QUESTION 7
What set of primitive signals is valid for arbitrated loop?
A. NOS, LOS, LR, LRR
B. SOF, EOF, ABTS, ACK
C. LIFA, LIPA, LIHA, LISA
D. LIP, LR, LRR, SOF
E. CLS, OPN, ARB
Correct Answer: E
QUESTION 8
If a Fibre Channel interface is receiving an NOS pattern on its interface, what pattern will the interface be transmitting?
A. OLS
B. LR
C. LRR
D. IDLE
E. NOS
Correct Answer: A
QUESTION 9
Fibre Channel Protocol is a protocol consisting of several layers. What are these layers, in
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 350-040
order from FC-0 to FC-4?
A. Media, Encode and Decode, Framing and Control, Common Services, Upper Level Protocol
B. Encode and Decode, Media, Framing and Control, Common Services, Upper Level Protocol
C. Framing and Control, Encode and Decode, Media, Common Services, Upper Level Protocol
D. Upper Level Protocol, Common Services, Framing and Control, Encode and Decode, Media
E. Media, Framing and Control, Encode and Decode, Common Services, Upper Level Protocol
Correct Answer: A

QUESTION 10
All of these are functions of LIP except which one?
A. reinitialize a loop
B. perform passive attachment to loop
C. indicate loop receiver failure
D. indicate which port to reset on loop
E. acquire an AL_PA
Correct Answer: B
QUESTION 11
What Fibre Channel header field indicates the frame is a Link Control frame?
A. R_CTL
B. CS_CTL
C. TYPE
D. F_CTL
E. DF_CTL
Correct Answer: A
QUESTION 12
What Fibre Channel transport functions can be found at the FC-2 level?
A. Exchange Operation, Information Unit, and Sequence
B. Session, Exchange, and Information Unit
C. Sequence, Frame, and Flow Control
D. Sequence, Frame, and Information Unit
E. Exchange Management, Link Control, and Flow Control
Correct Answer: C

The Most Recommended Cisco 350-040 Certification From Pass4itsure.com For Free Download

Exam A
QUESTION 1
A customer has an existing production fabric with Brocade and McData FC switches intermixed. When adding an MDS 9000 switch, what MDS interop mode would be required? (Topology: McData 6400 – (ISL)
–
Brocade12000 – (ISL) — MDS)

A.
Open Fabric Mode

B.
Native

C.
Interop 1

D.
Interop 2

E.
Interop 3
Correct Answer: C
QUESTION 2
MDS3_9509# MDS3_9509# dir bootflash: 1106 Dec 08 15:36:14 2003 MDS20031208072937365.lic 1106 Dec 08 15:44:47 2003 MDS20031208074023541.lic 2562 Jun 13
17:25:32 2004 special_config.txt 558 Jun 08 20:25:17 2004 create_mds3_fcalias.script 12288 Dec 04
18:04:10
2003 lost+found/ 12317696 Apr 09 15:41:02 2004 m9500-sf1ek9-kickstart-mz.1.3.4.bin 12334592 May 05 19:13:47 2004 m9500-sf1ek9-kickstart-mz.1.3.4b.bin 43659162 Apr 09 15:42:12 2004 m9500-sf1ek9-mz.1.3.4.bin 43687917 May 05 19:13:30 2004 m9500-sf1ek9-mz.1.3.4b.bin 3222 Mar 26 18:40:02 2004 script_b_fcip Usage for bootflash://sup-local 126206976 bytes used 58352640 bytes free 184559616 bytes total MDS3_95 What command would successfully transfer the “special_config.txt” file to a workstation, PC, or File Server?

A.
copy special_config.txt ftp://<ipaddress>/<path>/special_config.txt

B.
copy bootflash:special_config.txt ftp://<ipaddress>/<path>/special_config.txt

C.
copy <ftp://bootflash:special_config.txt> <ip address>/<path>/special_config.txt

D.
copy <ftp://<ip> address>/<path>/<filename> special_config.txt

E.
copy special*.txt ftp://<ipaddress>/<path>/special_config.txt
Correct Answer: B
QUESTION 3
In a long distance link of 100KM, which is true of the desired number of BB credits?
A. More BB credits would cause excessive delay in handling the larger number of packets.
B. The fewer the BB credits there are, the less likely we are to have a packet lost in the network.
C. With fewer BB credits, the transmission pipe will not be full and this will lead to other applications getting bandwidth should they need it.
D. The FC standard defines the number of credits on a long distance link.
E. None of the above answers are correct.
Correct Answer: E
QUESTION 4
During principal switch selection and the domain ID assignment, all frames are flooded to a destination ID of this well known fibre channel address:
A. FF.FF.FA
B. FF.FF.FB
C. FF.FF.FC
D. FF.FF.FD
E. FF.FF.FE
Correct Answer: D QUESTION 5

A Brocade 12000 in its native corePID mode (1) is connected to VSAN 1009 on an MDS. What is the correct output of the “show vsan 1009” command?
A. vsan 1009 information name:VSAN1009 state:active interoperability mode:default loadbalancing:src-id/ dst-id/oxid operational state:up
B. vsan 1009 information name:VSAN1009 state:active interoperability mode:1 loadbalancing:src-id/dst-id/oxid operational state:up
C. vsan 1009 information name:VSAN1009 state:active interoperability mode:2 loadbalancing:src-id/dst-id/oxid operational state:up
D. vsan 1009 information name:VSAN1009 state:active interoperability mode:3 loadbalancing:src-id/dst-id/oxid operational state:up
E. vsan 1009 information name:VSAN1009 state:active interoperability mode:Brocade Native loadbalancing:src-id/dst-id/oxid operational state:up
Correct Answer: D
QUESTION 6
You have a legacy JBOD that uses copper DB-9 connecters. You want to connect your JBOD to a Fiber only Fibre Channel switch. You want to convert the DB-9 connection to multi mode Fiber Optics. What device would you use?
A. HSSC
B. MIA
C. GBIC
D. SFP
E. DUAL SC
Correct Answer: B
QUESTION 7
To capture all of the RSCN traffic originating from a standalone switch with no free ports, what should be utilized?
A. SPAN
B. REMOTE SPAN
C. Ethereal with PAA
D. debug rscn events initiators vsan 1000
E. MDS fcanalyzer
Correct Answer: E
QUESTION 8
You have a host that you connect to a switch port on a MDS switch. The switch port does not come up and a “show interface” indicates that the port is initializing and eventually goes offline. You configure the port as a TL port and the port comes up. What type of device is the host?
A. Public loop device
B. Private loop device
C. Non Fibre Channel device
D. The host has a DB-9 copper connector
E. The port should not come up after being configured as TL port because TL ports are used to connect to other switches.
Correct Answer: B
QUESTION 9
MDS Interop mode 2 will interoperate with what legacy Fibre Channel switch below?
A. Brocade 12000 core PID mode 1
B. Brocade 3800 core PID mode 0
C. Inrange FC/9000
D. McData 3900
E. Qlogic Sanbox
Correct Answer: B
QUESTION 10
What is TCP fast recovery?
A. It is an algorithm that uses fast retransmit when a missing segment is detected.
B. It is an algorithm that initiates slow start instead of congestion avoidance after fast retransmit sends what appears to be the missing segment.
C. It is an algorithm that starts congestion avoidance instead of slow start after fast retransmit sends what appears to be the missing segment.
D. It is an algorithm that after a new connection is established with a host on another network, initializes the congestion window to one segment and each time an ACK is received, increases the congestion window by one segment
Correct Answer: C
QUESTION 11
Before you can successfully enable the Call Home feature, which of the following must be true?
A. snmp-server contact name defined
B. callhome site-id defined
C. Enterprise license installed
D. callhome transport email smtp-server defined
E. snmp-server location defined
Correct Answer: A

Updated Cisco 350-040 exam questions and 350-040 braindumps from Flydumps. Pass the Cisco 350-040 exam with our https://www.pass4itsure.com/350-040.html VCE dumps. Free try the 350-040 PDF demo.

Exam A
QUESTION 1
Which statements are true about a cascaded FICON topology? Select three.
A. It requires Fabric binding to be configured in all the switches.
B. Only one hope (ie:traversing 2 switchs) is supported.
C. Separate ISLs must be used dedicated to FICON traffic.
D. Two byte link addressing as defined in FC-SB2, is mandatory.
Correct Answer: ABD
QUESTION 2
MDS3 _ 9509# install all system bootflash:m9500-sf1 ek9-mz.1.3.4.bin kickstart bootflash:m9500-sfek9-kickstart-mz.1.3.4.bin Verifying image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% –SUCCESS Verifying image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% –SUCCESS Extracting “sic”version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% — SUCCESS Extracting “ips” version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% — SUCCESS Extracting “system” version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% — SUCCESS Extracting “kickstart”version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% — SUCCESS Extracting “loader” version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin [####################] 100% — SUCCESS Compatibility check is done: Module bootable impact install-type reason ——— ——— ———- ——- —– ——— 2 yes non-disruptive rolling 3 yes disruptive rolling Hitless upgrade is not supported 5 yes non-disruptive reset 6 yes non-disruptive reset Images will be upgraded according to following table: Module Image Running-Version Net-Version Upg-Required ——— ——- ———- ———– —— ———- 2 slc 1.3(4b) 1.3(4) yes 2 bios v1.1.0(10/24.03) v10.8(08/07/03) no 3 slc 1.3(4b) 1.3(4) yes 3 bios v1.1.0(10/24.03) v10.8(08/07/03) no 5 system 1.3(4b) 1.3(4) yes 5 kickstart 1.3(4b) 1.3(4) yes 5 bios v1.1.0(10/24.03) v10.8(08/07/03) no 5 loader 1.2(2) 1.2(2) no 6 system 1.3(4b) 1.3(4) yes 6 kickstart 1.3(4b) 1.3(4) yes 6 bios v1.1.0(10/24.03) v10.8(08/07/03) no 6 loader 1.2(2) 1.2(2) no Do you want to continue with the installation (y/n)? [n] What is the reason the upgrade would not be hit-less for the entire switch, above?
A. The supervisor module requires a BIOS upgrade, which is disruptive.
B. The “rolling-upgrade” for module 2 requires a second “slc” to be hit-less.
C. Module 3 is an IPS-8 card, which does not support non-disruptive downgrades.
D. Nodule 3 is an IPS-8 and the switch does not have a second IPS-8 card for route diversity which could provide a “stable” upgrade.
E. No reason – the upgrade is non-disruptive and hit-less.
Correct Answer: C
QUESTION 3
Which methods can be used to control Iscsi INITIATOR ACCESS TO VIRTUAL TARGETS? Select three.
A. Zoning
B. Specifying on which Gigabitethernet port the virtual target is advertised.
C. Setting up Iscsi PROXY MODE FOR THE INITIATORS
D. Specifying which IP subnet virtual target can be accessed
E. Enabling role-based access control.
Correct Answer: ABC
QUESTION 4
In a scenario with three lSLs between two switches, a single host in VSAN 5 on switch A, and a single storage device on switch B in the same VSAN. What would be the effect on the lSLs if Flow based load balancing option was enabled in VSAN 5?
A. Each subsequent frame will use the least utilized link, based on FCC.
B. Each subsequent frame will use a different link.
C. All frames between source and destination would follow same link for given flow.
D. Flow based load balancing is not enabled for an individual VSAN.
Correct Answer: C
QUESTION 5
Which organization produce standards related to SCSI, Fiber Channel or Fiber Channel protocol? Select two.
A. SNIA
B. T11 Committee
C. Cisco Systems
D. T10 Committee
E. T12 Committee
Correct Answer: BD
QUESTION 6
What is the User-specified VSAN Ids range?
A. 1-4093
B. 2-4093
C. 2-4094
D. 2-4092
Correct Answer: B

QUESTION 7
What can be configured on a FCIP Profile?
A. Max and Min bandwidth, peer-info, compression ratio
B. Passive mode, peer-info, compression ratio
C. TCP port number, sack-enable, Max and Min bandwidth
D. Sack-enable, TCP port number peer-info
E. TCP port number, write accelerator compression ratio
Correct Answer: C
QUESTION 8
A Brocade 12000 in its native corePID mode (1) is connected to VSAN 1009 on an MDS. What is the correct output of the “show vsan 1009” command?
A. vsan 1009 information: name: VSAN 1009 state:active interoperability mode:default loadbalancing:src-id/dst-id/oxid operational state:up.
B. vsan 1009 information: name: VSAN 1009 state:active interoperability mode:1 loadbalancing:src-id/dst-id/oxid operational state:up.
C. vsan 1009 information: name: VSAN 1009 state:active interoperability mode:2 loadbalancing:src-id/dst-id/oxid operational state:up.
D. vsan 1009 information: name: VSAN 1009 state:active interoperability mode:3 loadbalancing:src-id/dst-id/oxid operational state:up.
E. vsan 1009 information: name: VSAN 1009 state:active interoperability mode:Brocade Native loadbalancing:src-id/dst-id/oxid operational state:up.
Correct Answer: D
QUESTION 9
What TCP feature reduces the chances of an oversized IP packets from being fragmented?
A. SACK
B. Extended ping
C. PMTU
D. Retransmit timeout
E. Send buffer size
Correct Answer: C
QUESTION 10
In Raid 0+1 the loss of a single drive:
A. Does not affect the redundancy of the array
B. Reduces the array redundancy to that of a Raid level 0
C. Same level of redundancy to that of a Raid level 1+0
D. Reduces the performance of the array
E. Has no affect what so ever on the array
Correct Answer: B

QUESTION 11
Which are functions of the Domain identifier Assigned (DIA) ILS? Select two
A. It indicates that a Principal Switch has been selected, and that the upstream neighbor Switch has been assigned a Domain identifier.
B. It indicates that the receiving Switch can proceed requesting a Domain Identifier.
C. It indicates that the principal switch selection and address assignment phase is completed and the fabric is operational.
D. It indicates that the principal switch selection is started, but a principal switch has not been identified yet.
E. It indicates that a Request Domain Identifier ILS has been received by principal switch.
Correct Answer: AB
QUESTION 12
What zoning option can be used in interop mode 2 and 3?
A. domain / port
B. nWWN
C. fcid
D. lin zoning
E. sWWN
Correct Answer: A

read more: latest https://www.pass4itsure.com/350-040.html dumps 2017