Passed with high score today for pass for it sure Cisco 642-587 Exam. Windows 8.1 new questions will be added so I’m lucky to pass today.Almost all questions were the same includes the new question, DirectAccess, EFS, AD CS..Only used Flydumps premium vce file.
Exam A QUESTION 1
Look at the picture.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
Answer: Check certifyme eEngine, Download from Member Center
QUESTION 2
To implement the optional phase zero when using EAP-FAST for authentication, which of the following parameters must be set on the Cisco Secure ACS?
A. authority ID info
B. client initial message
C. EAP-FAST master server
D. Allow automatic PAC provisioning
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 3
An 802.1X client cannot authenticate to an autonomous access point configured for multiple VLANs. The native VLAN does not have an SSID configured. Which one of the following links being down would prevent the clients from authenticating?
A. between the client’s VLAN and the WLSE
B. between the native VLAN and the WLSE
C. between the RADIUS and the access point
D. between the client’s VLAN and the RADIUS
Correct Answer: C Section: (none) Explanation
Explanation/Reference: QUESTION 4
How many WLANs can a REAP support when actively connected to a wireless controller?
A. 4
B. 8
C. 16
D. 32
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Which of the following power settings represents 50 percent power in a lightweight access point?
A. 1
B. 2
C. 3
D. 4
E. 5
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 6
A blinking green power LED indicates which of the following conditions on a Cisco Series 1000 lightweight access point?
A. startup
B. site survey mode
C. duplicate IP address
D. lost connection to the controller
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 7
On the WLSE, which of the following tasks must be completed before Interference Detection can be enabled?
A. Enable Self-Healing.
B. Conduct Radio Scan.
C. Conduct Client Walkabout.
D. Configure Location Manager.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 8
An REAP was supporting 16 WLANs, but now it only supports one. What happened to cause the change?
A. An access point firmware upgrade is in progress.
B. The access point lost its configuration.
C. Controller connectivity has been lost.
D. The access point was rebooted.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 9
You are installing a Cisco 4402 Series Wireless LAN Controller. What type of interface is used on the uplink port?
A. 10/100 Mbps RJ45
B. 1000Base-X Mini-GBIC
C. 10/100/1000 Mbps RJ45
D. 1000Base-SX
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 10
You are trying to deploy a configuration job to an IOS access point using the WLSE, but the job fails. Which of the following would cause this failure?
A. SNMP communities
B. WLCCP credentials
C. HTTP user/password
D. Telnet/SSH user/password
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 11
You are conducting a CDP-based discovery using an edge switch for the seed. There is a router between the switch and the WLSE. None of the access points are discovered, and the discovery log shows the switch is SNMP unreachable. What is the problem?
A. The SNMP communities on the router do not match the WLSE.
B. The SNMP communities on the switch do not match the WLSE.
C. The SNMP communities on the access points do not match the WLSE.
D. The SNMP communities on the access points do not match the switch.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 12
When installing a Cisco WCS, which two ports can be changed during installation? (Choose two.)
A. HTTPS
B. HTTP
C. TFTP
D. RMI
E. FTP
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Using the WLSE, you are trying to push out a configuration job to an access point, but the job does not start. Which of the following would cause this failure?
A. invalid parameter in the template
B. pop-up blocker enabled in the browser
C. incorrect SNMP communities on the access point
D. unsupported version of IOS firmware in the access point
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 14
Client exclusion policies are used to mitigate which of the following attacks?
A. dictionary
B. MAC spoofing
C. man-in-the-middle
D. bit-flip and replay
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 15
To keep performance optimal on a lightweight access point, what can be done?
A. Disable Auto RF and configure manually.
B. Power access point to full power.
C. Disable all 802.11b data rates.
D. Hard code the channel.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 16
Your client has deployed a Cisco Wireless Location Appliance within their warehouse environment. They
have been experiencing problems with tracking objects using active RFID tags. The RFID beacon rate is
10 seconds. You have discovered an issue with the RFID timeout value.
How should this value be changed?
A. Change the value on the Cisco WCS to 95 seconds.
B. Change the value on the Cisco WCS to 45 seconds.
C. Change the value on the wireless controller to 95 seconds.
D. Change the value on the wireless controller to 45 seconds.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 17
Two access points running the core feature set are connected to the same switch and are providing guest services. If PSPF is enabled, what must be enabled on the switch to prevent clients from seeing one another’s data?
A. inline power
B. protected port
C. 802.1q trunking
D. port-based RADIUS
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 18
There are 30 managed access points on the WLSE. A radio scan is started but fails. Upon inspection of the device list in the reports tab, you notice a red indicator on the WDS access point. Upon inspection of the WDS access point through its GUI, it is discovered that the security keys are not set up between the WDS access point and the WLSE. Which of the following is misconfigured?
A. SNMP communities
B. WLCCP credentials
C. HTTP user/password
D. Telnet/SSH user/password
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 19
VLANs have been enabled on an autonomous access point. In order for clients associating to VLANs other than the native VLAN to receive an IP address, which of the following must be configured?
A. switchport set to SSL trunking
B. switchport set to 802.1q trunking
C. access point Ethernet port set to SSL trunking
D. access point Ethernet port not set to 802.1q trunking
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 20
What three search criteria does Cisco WCS use to search for wireless controllers? (Choose three.)
A. MAC address
B. outdoor area
C. controller name
D. floor area
E. IP address
F. networks
Correct Answer: CEF Section: (none) Explanation
Explanation/Reference:
We provide Cisco 642-587 help and information on a wide range of issues.Cisco 642-587 is professional and confidential and your issues will be replied within 12 hous.Cisco 642-587 free to send us any questions and we always try our best to keeping our Customers Satisfied.