Apple 9L0-003 Qs&As, Pass the Apple 9L0-003 Exam Materials Sale

Flydumps presents the highest quality of Apple 9L0-003 practice material which helps candidates to pass the pass4itsure.com Apple 9L0-003 exams in the first attempt.The brain dumps are the latest,authenticated by expert and covering each and every aspect of Apple 9L0-003 exam.

QUESTION 11
You have replaced the video card in a Power Macintosh G4 (FW 800). In what THREE ways should you test the repair before running the system to the customer? (Choose three)
A. Leave the computer on overnight.
B. Verify that the original symptom is resolved.
C. Verify that no new symptoms have occurred.
D. Start up the computer in Target Disk Mode to test the internal hard drive.
E. Run all Apple Service Diagnostic tests for the Power Mac G4 (FW 800).
F. Run Apple Service Diagnostic video tests for the Power Mac G4 (FW 800).

Correct Answer: BCE
QUESTION 12
An eMac has no video, but powers on with a normal startup chime, and normal startup sounds from the hard drive. Which of the following steps should you try next?
A. Update the eMac firmware.
B. Replace the eMac logic board.
C. Replace the eMac Display/Analog Assembly.
D. Connect a known-good VGA display to the eMac.

Correct Answer: D
QUESTION 13
You are troubleshooting an intermittent video issue on an eMac. Which of the following is them most appropriate way to approach this problem?
A. Do nothing. The problem may resolve itself.
B. Run looping diagnostics to verify the issue.
C. Follow component isolation steps to resolve the issue.
D. Replace the Display/Analog Assembly inside the eMac.
Correct Answer: B
QUESTION 14
Which of the following is ALMOST CERTAINLY a software-related problem?
A. No video display
B. Low disk space warning
C. Single beep at startup
D. No Internet connectivity

Correct Answer: B
QUESTION 15
You are troubleshooting a Power Mac G5 that will not boot, and emits error tones when powered on. You suspect that the customer may have installed incompatible or faulty RAM, but you are not sure. What should you do to verify the RAM requirements for this Power MAC G5?
A. Call Apple
B. Order Apple RAM
C. Check Specifications
D. Count the RAM sockets on the logic board

Correct Answer: C
QUESTION 16
You are troubleshooting a Power Mac G5 that has the following symptom: The power-on LED illuminates when the power button is pressed, fans spin, and the boot tine chimes, but there is no video displayed on the attached know-good display. Rank the following possible causes from First to Last, in the order you should check them:
1.
Crashed PMU

2.
Faulty logic board

3.
Corrupted PRAM

4.
Video card not fully seated in logic board connector

5.
Faulty video card
A. 1, 3, 4, 5, 2
B. 2, 1, 4, 3, 5
C. 3, 1, 4, 5, 2
D. 4, 3, 5, 1, 2
E. 5, 1, 2, 4, 3

Correct Answer: D
QUESTION 17
An eMac (USB 2.0) is displaying a flashing question mark at startup. When you start up the computer from a known-good bootable external FireWire hard drive the internal hard drive does not appear on the desktop. What is the recommended order in which to attempt the following troubleshooting steps on the internal hard drive?
1.
Replace the hard drive.

2.
Reinitialize the hard drive.

3.
Replace the hard drive cable.

4.
Verify the hard drive’s cable connections.

5.
Reinstall the software drivers for the hard drive.
A. 1, 3, 4, 2, 5
B. 2, 1, 3, 5, 4
C. 3, 1, 4, 5, 2
D. 4, 1, 5, 2, 3
E. 5, 4, 2, 3, 1

Correct Answer: E
QUESTION 18
A customer states that he cannot open an AppleWorks file. What is the most productive question to ask him FIRST?
A. Can you open any files?
B. Can you open other AppleWorks files?
C. What version of AppleWorks are you using?
D. In your Mac connected to a network?

Correct Answer: B
QUESTION 19
A hard dive in a Power Mac G4 (QuickSilver) is not spinning after the computer is powered on. You have verified that the drive power cable connector has no voltage by using a voltmeter. Which of the following is the most appropriate part or module to replace in this situation?
A. Hard Drive
B. Hard Drive Data Cable
C. Power Supply Assembly
D. Cable Harness Assembly

Correct Answer: C
QUESTION 20
Which THREE of the following computers uses Serial ATA hard drive technology? Select three.
A. Power Mac G4 (FW 800)
B. Power Mac G5 (Uni 1.6GHz)
C. Power Mac G5 (Dual 2.0 GHz)
D. Power Mac G4 (Mirrored Drive Doors)
E. Power Mac G5 (June 2004 Dual 2.5 GHz)

Correct Answer: BCE
QUESTION 21
A customer states that he has never been able to burn DVD’s with his eMac (USB 2.0), yet his friend has an identical-looking eMac (USB 2.0) that can burn DVD’s. You have verified that the customer’s eMac (USB 2.0) has a DVD / CD-RW Combo optical drive and is running the latest version of Mac OS X. The eMac has no other problems. What is the probable cause is this issue?
A. The eMac (USB 2.0) requires more RAM.
B. The eMac (USB 2.0) requires a firmware update.
C. The Combo drive is not capable of burning DVD’s.
D. The eMac (USB 2.O) optical drive is malfunctioning.

Correct Answer: C
QUESTION 22
You are working on an eMac that has no video on its built-in display. The fan is spinning, and there is drive activity present. You have tried resetting PRAM, booting to a known-good CD, and resetting the PMUm but the issue persists. You have also connected a known-good external VGA monitor to the eMac’s video out port, but failed to see any video on the external display. Which of the following is the most appropriate part or module to replace in this situation?
A. CRT
B. Logic Board
C. Power Supply
D. Display / Analog Assembly

Correct Answer: B
QUESTION 23
Which THREE of the following symptoms would be best resolved by performing a PMU reset as a first step? (Choose three)
A. Network / Internet connectivity issue.
B. No power / computer does not function.
C. Cursor randomly freezes on the display.
D. USB and/or FireWire port(s) do not function.
E. Computer does not sleep / wake from sleep.
Correct Answer: BCE
QUESTION 24
Which TWO of the following features are part of the Universal Motherboard Architecture in Apple desktop computers? (Choose two)
A. VGA
B. USB
C. FireWire
D. Target Disk Mode
E. Power Manager 2.0
F. Hardware DVD decoding

Correct Answer: CE
QUESTION 25
A Power Mac G5 fails to start up, and the status light on the front of the computer flashes three times.
What does this indicate?
A. Thermal failure
B. No startup disk found
C. Firmware v3.0 upgrade required
D. No RAM bank passed memory testing

Correct Answer: D
QUESTION 26
Which of the following Power Mac G5 internal fans can only be replaced by replacing the entire G5 enclosure?
A. Front inlet fan
B. Rear exhaust fan
C. Media blower / fan
D. Speaker / fan assembly
E. Power supply fan assembly

Correct Answer: C
QUESTION 27
Which TWO of the following computers can accept a 184-pin DDR333 PC2700 SDRAM DIMM? (Choose two)
A. iMac (Flat Panel)
B. eMac (USB 2.0)
C. Power Mac G5 (Uni 1.6Ghz)
D. Power Mac G5 (Dual 2.0 Ghz)
E. Power Mac G5 (June 2004 Dual 2.5 Ghz)
Correct Answer: BC
QUESTION 28
What is the function of the PMU in an Apple desktop computer?
A. The PMU controls all aspects of power flow.
B. The PMU controls the speed of the hard drive.
C. The PMU manages the amount of virtual memory used.
D. The PMU manages all communication with attached peripherals.
Correct Answer: A QUESTION 29
A Power Mac G5 sometimes becomes unresponsive and the cursor freezes on the display when running an application. You have verified the symptom, have already attempted to force the application to quit, but the computer remains unresponsive. What should you try next?
A. Hold the mouse button down for several seconds to regain cursor control.
B. Press the power button for several seconds to try shutting the computer down.
C. Disconnect and reconnect all peripherals to reset the Open Firmware Device Tree.
D. Disconnect the power cord and the backup battery for several minutes to reset the PMU.

Correct Answer: B
QUESTION 30
The fans inside a customer’s Power Mac G5 seem to constantly run at full speed after a repair involving logic board replacement. What should be done FIRST to correct this problem?
A. Replace the processor(s).
B. Run Apple Service Diagnostic.
C. Replace the fans inside the Power Mac G5.
D. Replace the Power Mac G5 logic board again.

Correct Answer: B
QUESTION 31
You are troubleshooting an eMac system that has Mac OS X. The icon of a connected external FireWire drive is not appearing on the Finder Desktop. Which of the following would be MOST useful in troubleshooting this issue?
A. Terminal
B. Network Utility
C. Process Viewer
D. System Profile
E. Apple Hardware Test

Correct Answer: D
QUESTION 32
A Macintosh can start up from Mac OS X, but not from Mac OS 9. If you select the Mac OS 9 System Folder in the Startup Disk preference pane of MAC OS X, a flashing question mark appears on the screen when you restart the computer. What is one possible cause of this condition?
A. The disk was reformatted using Disk Utility for Mac OS X, using the HFS Plus (extended) format instead of HFS format.
B. The disk was reformatted using Disk Utility for Mac OS X, and the option to install the Mac OS 9 drivers was not selected.
C. The disk was reformatted using Disk Utility for Mac OS X, using the HFS format instead of HFS Plus (extended) format.
D. This Macintosh does not support booting into Mac OS 9.

Correct Answer: B
QUESTION 33
What is the first step to take if you have an iMac (Flat Panel) that constantly ejects any CD / DVD that is inserted?
A. Replace the optical drive.
B. Replace the optical drive cable.
C. Replace the optical drive bezel.
D. Disconnect all peripheral devices, especially the mouse.

Correct Answer: D QUESTION 34
A customer needs to transfer data from her eMac for use on her Power Mac G5, but the eMac fails to start up completely due to a video issue.
Which of the following would most easily accomplish the data transfer?
A. Remove the hard drive from the eMac and install it into the Power Mac G5.
B. The eMac will need to be replaced before any data can be recovered from it.
C. Boot the eMac into Mac OS X Safe Mode and connect the eMac and Power Mac G5 with an Ethernet cable.
D. Boot the eMac into Target Disk Mode and connect the eMac and Power Mac G5 with a FireWire cable.

Correct Answer: D QUESTION 35
A Power Mac G4 (Mirrored Doors) displays a flashing question mark at startup. Which step does Apple recommend you take FIRST?
A. Reset Parameter RAM.
B. Try to start up from a bootable CD or DVD.
C. Reinitialize the hard disk and reinstall the Mac OS.
D. Replace the internal hard drive with a known-good hard drive.

Correct Answer: B QUESTION 36

All our Cisco products are up to date! When you buy any Apple 9L0-003 product from Certpaper, as “Apple 9L0-003 Questions & Answers with explanations”, you are automatically offered the Apple 9L0-003 updates for a total of 90 days from the day you bought it. If you want to renew your Apple 9L0-003 purchase during the period of these 90 days, your Apple 9L0-003 product is renewed and you are further enabled to enjoy the free Cisco updates.

Continue Reading

Apple 9A0-043 Exam Test Questions, 100% Pass Rate Apple 9A0-043 Free Dowload Is What You Need To Take

Flydumps bring you the best Apple https://www.pass4itsure.com/9a0-043.html exam preparation materials which will make you pass in the first attempt.And we also provide you all Apple 9A0-043 exam updates as Microsoft announces a change in its Apple 9A0-043 exam syllabus,we inform you about it without delay.

QUESTION 11
Which format should you use to export your Illustrator document to a vector file format that can be viewed in a Web browser?
A. GIF
B. EPS
C. SVG
D. JPEG
Correct Answer: C QUESTION 12
Which export format allows you to embed ICC profiles?
A. GIF
B. PNG
C. JPEG
D. Enhanced Metafile Correct Answer: C
QUESTION 13
What should you do to vertically dock one palette to another? Exhibit:

A. drag the Palette tab of one palette to the bottom of the other palette
B. drag the Palette tab of one palette into the Palette tab area of the other palette
C. use the Palette Options command on the Palette menu to designate the desired docked position
D. Alt-drag (Windows) or Option-drag (Mac OS) the Palette tab of one palette into the Palette tab area of the other palette

Correct Answer: A
QUESTION 14
You want to have Adobe Bridge act as a floating palette to easily drag assets into your Illustrator document. Which mode should you toggle?
A. Compact mode
B. Thumbnail mode
C. Details View mode
D. Ultra-compact mode

Correct Answer: A
QUESTION 15
You are using the Paintbrush tool to create paths with an Art brush applied to them. Every time you drag the Paintbrush tool over an existing selected path, the path shape changes. You want to be able to create a new path instead of changing an existing path. What should you do?
A. set Fidelity to zero
B. set Smoothness to zero
C. turn off Edit Selected Paths
D. turn on Fill New Brush Strokes
Correct Answer: C
QUESTION 16
You are creating artwork for animation and will export the artwork as a SWF file.
Which type of object should you use to greatly reduce the output size of the SWF file?
A. Mesh
B. Patterns
C. Symbols
D. Gradients

Correct Answer: C
QUESTION 17
When making default color management decisions, to what does a color management policy compare profiles?
A. the RGB working space
B. the CMYK working space
C. the current working space
D. the rendering intent that is currently selected
E. the color management engine that is currently selected

Correct Answer: C
QUESTION 18
You are configuring your Color Settings. You want to utilize color management but want CMYK values to be preserved when opening untagged documents. You also want to use an RGB working color space that is well suited for documents that will be converted to CMYK. Which default setting should you choose?
A. Monitor Color
B. North America Prepress 2
C. Emulate Adobe Illustrator 6.0
D. North America General Purpose 2

Correct Answer: B
QUESTION 19
You have an Illustrator document that you need to save as a legacy Illustrator document. Which is the oldest version that will preserve transparency?
A. Illustrator 8
B. Illustrator 9
C. Illustrator 10
D. Illustrator CS
Correct Answer: B
QUESTION 20
You want to add a gradient fill to your type. Which two menu options could you use? (Choose two.)
A. Type > Glyphs
B. Object > Expand
C. Type > Create Outlines
D. Object > Compound Path
E. Type > Area Type Options
Correct Answer: BC
QUESTION 21
In which palette do you find the option to align the stroke of your closed path to the outside?
A. Align palette
B. Stroke palette
C. Attributes palette
D. Appearance palette

Correct Answer: B QUESTION 22
You are saving a file to an Illustrator version earlier than 9.0. An option field within the dialog becomes active to allow you to determine what will happen to objects _____.
A. with links
B. containing type
C. containing PDF data
D. containing transparency

Correct Answer: D QUESTION 23
Refer to the exhibit.
You are using the Transform palette to scale a selected object. You notice the warning icon shown in the exhibit, at the bottom of the palette. What does this icon indicate will happen when you attempt to scale the object? Exhibit:

A. Only the object will be transformed.
B. Only the pattern of the object will be transformed.
C. Only the object and its strokes and effects will be transformed.
D. Both the object and the pattern of the object will be transformed.

Correct Answer: B
QUESTION 24
Which Web graphic format is resolution-independent?
A. PNG
B. SVG
C. JPEG
D. WBMB

Correct Answer: B
QUESTION 25
How should you display the alternate glyphs for a highlighted character?
A. select Access All Alternates in the Show list of the Glyphs palette
B. select Alternates for Current Selection in the Show list of the Glyphs palette
C. select Substituted Fonts in the Highlight area of the Document Setup dialog box
D. select Substituted Glyphs in the Highlight area of the Document Setup dialog box

Correct Answer: B
QUESTION 26
Which category of print options enables you to create color separations?
A. Setup
B. Output C. Advanced
D. Color Management

Correct Answer: B
QUESTION 27
How should you create a clipping mask by using the Layers palette?
A. arrange the objects on one layer with the clipping path on the top, select the layer and choose Make Clipping Mask from the Layers palette menu
B. arrange the objects on one layer with the clipping path on the bottom, select the layer and choose Make Clipping Mask from the Layers palette menu
C. arrange the objects on one layer with the clipping path on the top, select each separate object (not the layer) and choose Make Clipping Mask fromthe Layers palette menu
D. arrange the objects to be clipped on one layer and the clipping path on a separate layer above, select both layers and choose Make Clipping Mask from the Layers palette menu

Correct Answer: A
QUESTION 28
Refer to the exhibit.
Image A in the exhibit has no transparency applied. Which statement about Image B is true? Exhibit:

A. An opacity mask was applied.
B. Isolate blending was turned on.
C. The objects were grouped first, then transparency was applied.
D. The objects were selected individually and transparency was applied to each.

Correct Answer: C
QUESTION 29
You are printing a file with gradients, meshes, or color blends to a device that supports Postscript Language Level 2. You choose to rasterize these objects to improve print quality. To which format does Illustrator convert these objects?
A. GIF
B. EPS
C. TIFF
D. JPEG

Correct Answer: D
QUESTION 30
You are preparing an Illustrator file for color separation. Which color mode should your document be using?
A. RGB color
B. LAB color
C. HSB color
D. CMYK color

Correct Answer: D
QUESTION 31
Which icon should you click repeatedly to cycle through the views of a palette? Exhibit:

A. OPTION A
B. OPTION B
C. OPTION C
D. OPTION D

Correct Answer: B
QUESTION 32
You create an object using the Symbol Sprayer tool and change the color of several of the symbols within the object. What should you use to change a symbol back to the original color value?
A. Symbol Styler tool and the Alt (Windows) or Option (Mac OS) key
B. Symbol Shifter tool and the Alt (Windows) or Option (Mac OS) key
C. Symbol Stainer tool and the Alt (Windows) or Option (Mac OS) key
D. Symbol Screener tool and the Alt (Windows) or Option (Mac OS) key

Correct Answer: C
QUESTION 33
You want to export your Illustrator document to a raster file format that allows you to control image compression while retaining all of the color information. Which format should you choose?
A. GIF
B. EPS
C. PSD
D. JPEG
Correct Answer: D QUESTION 34
What does Adobe Bridge allow you to do?
A. browse files of all Adobe file formats
B. convert from one Adobe file format to another
C. edit metadata of any file format, Adobe or other
D. convert non-Adobe files to the most closely related Adobe file format

Correct Answer: A QUESTION 35
You are converting several vector objects to raster. Which should you select in the Rasterize dialog box so that you can control the resolution globally?
A. Screen (72 ppi)
B. High (300 ppi)
C. Anti-aliasing: None
D. Use Document Raster Effects Resolution

Correct Answer: D

Worried about Apple https://www.pass4itsure.com/9a0-043.html pass results? Adopt most reliable way of exam preparation that is Apple 9A0-043 Questions & Answers with explanations to get reliable high Apple 9A0-043 pass result.Flydumps definitely guarantees it!

Continue Reading

Apple 9A0-036 PDF, Latest Updated Apple 9A0-036 Study Guides Is Your Best Choice

Flydumps Apple 9A0-036 exam questions and answers in PDF are prepared by our expert, Moreover, they are based on the recommended syllabus covering all the Apple https://www.pass4itsure.com/9a0-036.html exam objectives.You will find them to be very helpful and precise in the subject matter since all the Apple 9A0-036 exam content is regularly updated and has been checked for accuracy by our team of Microsoft expert professionals.

QUESTION 11
You are recording an action. During its playback, you want an image’s magnification to be adjusted to fit the image on screen.
What should you do?
A. choose View > Fit on Screen
B. when you get to the point for the magnification change, choose View > Fit on Screen
C. use the Insert Menu Item command from the Action palette menu, then choose View > Actual Pixels
D. Use the Insert Menu Item command from the Action palette menu, then choose View > Fit on Screen

Correct Answer: D QUESTION 12
Exhibit.

The three images in the exhibit were scanned together. You apply the File>Automate>Crop and Straighten Photos command.
What is the result?
A. A separate layer is created for each image, excluding the white border, and each is rotated to correct for its crookedness.
B. A separate layer is created for each image, including some white border, and each is rotated to correct for its crookedness.
C. A separate document is created for each image, excluding the white border, and each is rotated to correct for its crookedness.
D. A separate document is created for each image, including some white border, and each is rotated to correct for its crookedness.

Correct Answer: C QUESTION 13
You want to modify the tonal range of an image without permanently affecting the pixels. What should you do?
A. use Variations
B. use Auto Levels
C. use a layer style
D. use an adjustment layer

Correct Answer: D QUESTION 14
What would you most likely need to do afterresamplinga 20 megabyte image to 100 kilobytes using BicubicInterpolation?
A. Blur
B. Sharpen
C. Add Noise
D. Auto Levels

Correct Answer: B QUESTION 15
Which option in the Auto Color Correction Options dialog box preserves the overall color relationship while making highlights appear lighter and shadows appear darker?
A. Snap NeutralMidtones
B. Find Dark & Light Colors
C. Enhance Per Channel Contrast
D. Enhance Monochromatic Contrast Correct Answer: D
QUESTION 16
You are trying to lighten only the darkest shadows in an image by choosing Image > Adjustments > Shadow/Highlight. You notice that lighter areas are being affected as well.
What should you do?
A. increase the Radius setting
B. decrease the Radius setting
C. increase the Tonal Width setting
D. decrease the Tonal Width setting

Correct Answer: D QUESTION 17
You are working in the Levels dialog box. The pixels in the image cover a range from 0-220. You want to increase the contrast in the highlight areas of the image.
What should you do?
A. increase the value for the black Input Level
B. decrease the value for the white Input Level
C. increase the value for the black Output Level
D. decrease the value for the white Output Level

Correct Answer: B QUESTION 18
You are using the Shadow/Highlight command to correct an underexposed image. Which value determines the scale size for corrections?
A. Radius
B. Amount
C. Tonal Width
D. MidtoneContrast

Correct Answer: A QUESTION 19
An overexposed photograph has nearly no detail in its highlights, but otherwise has acceptable tonal balance.
Which option from the Image > Adjustments menu should you use to reveal the details in the highlights?
A. Gradient Map
B. Channel Mixer
C. Shadow/Highlight
D. Brightness/Contrast

Correct Answer: C QUESTION 20
You want to crate a diagonal elliptical marquee. What should you do?
A. hold down the spacebar and rotate the marquee while dragging with the Elliptical Marquee tool
B. create a marquee with the Elliptical Marquee tool, then rotate it by choosing Edit > Free Transform
C. create a marquee with the Elliptical Marquee tool, then rotate it by choosing Select > Transform Selection
D. While dragging with the Elliptical Marquee tool, hold down Alt (Windows) or Option (Mac OS) and rotate the marquee

Correct Answer: C QUESTION 21
You have a photo of a green leaf. The leaf is in sharp focus and is against a blurred green background.
You want to make a selection that follows the contour of the leaf.
What should you do?

A. use the Find Edges filter
B. use the Magic Wand tool
C. use the Magnetic Lasso tool
D. choose Select >ColorRange

Correct Answer: C QUESTION 22
You have saved as selection as a channel. You now want to load and reuse the selection. What should you do?
A. drag the alpha channel into the image window
B. Alt (Windows) or Option (Mac OS) click on the alpha channel
C. Ctrl (Windows) or Command (Mac OS)click on the alpha channel
D. Right-click (Windows) or Control-click (Mac OS) on the channel and choose Load Channel as Selection

Correct Answer: C QUESTION 23
You have created a rough selection of an object in your image. You want to refine the selection by suing quick mask with its default settings and the Brush tool.
Which statement is true?
A. Painting with white adds to the selection
B. Painting with black adds to the selection.
C. The opacity setting of the brush is irrelevant.
D. The foreground color must be either black or white.

Correct Answer: A QUESTION 24
You have made a feathered selection. You then repeatedly fill the selected area with different colors. Which statement is true?
A. Traces of the earlier color fills remain at the feathered edges of the selection.
B. At the feathered edges of the selection only the image’s luminosityareaffected, not its hue or saturation.
C. At the feathered edges of the selection only the image’s hue and saturation area affected, not its luminosity.
D. Though fading in opacity at the feathered edges of the selection, the newer fills completely overwrite the earlier ones.

Correct Answer: A
QUESTION 25
Exhibit.

Which tool can completely eliminate the white pixels in the background of the image shown in the exhibit with a single click?
A. Eraser
B. Extract
C. Magic Eraser
D. Color Replacement

Correct Answer: C QUESTION 26
You have been editing an image. You want to restore certain small areas of the image to their condition before your last several edits.
Which tool or command should you use?
A. Eraser tool
B. Edit > Undo
C. History Brush tool
D. Edit > Step Backward

Correct Answer: C QUESTION 27
You are suing the Pattern Stamp tool to paint in your image.
Which tool option ensures that the pattern is applied continuously, rather than from the initial sampling point, regardless of how many times you stop and resume painting with the pattern?
A. Flow
B. Aligned
C. Impressionist
D. Protect Texture

Correct Answer: B QUESTION 28
Exhibit.

In the exhibit, which gradient was used to create the result to the right?
A. Angle Gradient
B. Redial Gradient
C. Diamond Gradient
D. Reflected Gradient

Correct Answer: C QUESTION 29
Which option from the Brushes palette allows you to determine the number and placement of marks in a stroke?
A. Texture
B. Scattering
C. Shape Dynamics
D. Brush Tip Shapes

Correct Answer: B QUESTION 30
Exhibit.

You want to create a shape layer by drawing in a freeform manner.
Which two buttons from the Vector Tools Options Bar should you choose? (Choose two.)

A. A
B. B
C. C
D. D
E. E
Correct Answer: AD

Apple 9A0-036 Questions & Answers with explanations is all what you surely want to have before taking Apple 9A0-036.Apple https://www.pass4itsure.com/9a0-036.html Interactive Testing Engine is ready to help you to get your Apple 9A0-036 by saving your time by preparing you quickly for the Cisco exam. If you are worried about getting your Apple 9A0-036 certification passed and are in search of some best and useful material, Apple 9A0-036 Q&A will surely serve you to enhance your Interconnecting Cisco Networking Devices Part 1 stydy.

Continue Reading

Ensure Pass Apple 9L0-615 Shares Latest Apple 9L0-615 FlyDumps New Questions for Apple 9L0-615 Exam 100% Valid

Ensure that you are provided with only the best and most updated Apple 9L0-615 Certification training materials, we also want you to be able to access them easily, whenever you want.We provide all our Apple https://www.pass4itsure.com/9l0-615.html Certification exam training material in PDF format, which is a very common format found in all computers and gadgets. Now we add the latest Apple 9L0-615 content and to print and share content.

Exam A
QUESTION 1
Which comparison of Mac OS X Server and Windows user account password policy enforcement is TRUE?
A. Mac OS X Server does not let you set inactivity limits on user account passwords, but Windows does.
B. Both Mac OS X Server and Windows allow you to enforce a minimum length for user account passwords.
C. Neither Mac OS X Server nor Windows has a graphical user interface for entering user account password policies.
D. Both Mac OS X Server and Windows require that user account passwords be different from account names.
E. Mac OS X Serverlets you require that account passwords be different from account names, but Windows does not.

Correct Answer: A
QUESTION 2
How do you configure an Apple Remote Desktop admin computer to use a remote Task Server?
A. Run the cfgtaskserver command line utility with the Task Server’s IP address as its parameter.
B. Open Remote Desktop and select your Task Server from the list that appears in the Task Server window.
C. Open Remote Desktop on the Task Server, and type the host name or lP address of the ARD admin computer.
D. Open Remote Desktop and select “Use remote Task Server” in the Task Server preferences pane of Remote Desktop, then enter the host name or IP address of your Task Server.

Correct Answer: D
QUESTION 3
In Workgroup Manager, which managed preference pane lets you configure proxy server settings for accounts?
A. Sharing
B. Internet
C. Network
D. Applications
E. System Preferences
Correct Answer: C
QUESTION 4
What is the maximum number of computers that can appear in the All Computers list in Remote
Desktop?
A. 1,000
B. 10,000
C. There is no defined upper limit.
D. The upper limit depends on your user license.

Correct Answer: D
QUESTION 5
In Workgroup Manager, which management frequency cannot be used to manage the System Preferences for accounts?
A. Never
B. Once
C. Often
D. Always

Correct Answer: B
QUESTION 6
Which Login preference can you set in Workgroup Manager for computer lists, but not for users or for groups?
A. Enable Fast User Switching
B. Open Specified Items at Login
C. Add Network Home Share Point
D. Hide Opened Login Items after Login

Correct Answer: A
QUESTION 7
How must you authenticate if you want to create a managed network view?
A. You must authenticate in the managed domain as a domain administrator.
B. You must authenticate with the Apple Remote Desktop password on your server computer.
C. You must authenticate as an administrator on the Mac OS X Server computer that manages your domain.
D. No special authentication is required; anyone can use Network preferences to create a network view named ‘Managed” which will be managed automatically by the Mac OS X Server computer that manages your domain.

Correct Answer: A
QUESTION 8
You want your Mac OS X Server to provide SMB service. What directory service role should it be
configured to use?
A. The Mac OS X Servers role must be Domain Member.
B. The Mac OS x Server’s role must be Standalone Server.
C. The Mac OS X Server’s role must be Backup Domain Controller.
D. The Mac OS X Server’s role must be Primary Domain Controller.
E. The Mac OS X Server can use any directory service role available.

Correct Answer: E
QUESTION 9
Which statement best describes how you configure managed Applications preferences in Workgroup Manager?
A. You create a list of users who can open any application on the local drive.
B. You create a list of users who can open specified applications when logged into their mobile account.
C. You select an account, then create a list of applications that can or cannot be opened by that account.
D. You create a list of approved or unapproved applications, then apply the list to selected user accounts.

Correct Answer: C
QUESTION 10
You can generate client computer reports on your Apple Remote Desktop admin computer, but not using your remote ARD Task Server. What is the most likely cause of this problem?
A. SSH is disabled on client computers.
B. The Mac OS X firewall is blocking port 22.
C. The Mac OS X firewall is blocking port 3283.
D. The network DNS is improperly configured.

Correct Answer: C

Get certified Apple 9L0-615 is a guaranteed way to succeed with IT careers. We help you do exactly that with our high quality ISC Apple https://www.pass4itsure.com/9l0-615.html Certification Certified Information Systems Security Professional training materials.

Continue Reading

Buy Latest Apple 9L0-206 PDF Download,Apple 9L0-206 PDF Questions For Groundbreaking Results

The Apple 9L0-206 certification can make you a competent person. It may enable a technician to know about the Apple https://www.pass4itsure.com/9l0-206.html configurations, get information about the Apple 9L0-206 data center products and hardware and knowledge about Apple 9L0-206 united computing systems.

Exam A
QUESTION 1
What tool does the service manual recommend you use to separate plastics and lift components of PowerBook and iBook computers?
A. Nylon probe tool
B. Jeweler screwdriver
C. Flatblade screwdriver
D. Precision needle nose pliers
Correct Answer: A
QUESTION 2
Which TWO of the following are true statements about screws inside a PowerBook or iBook?
A. All screws are interchangeable.
B. It is not necessary to replace all screws after a repair.
C. Screws should always be only comfortably tightened.
D. Screws should always be tightened as much as possible.
E. Screws should always be replaced exactly where they came from.
F. Torx and Hex (Allen) screws can both be driven by either type of driver.
Correct Answer: CE
QUESTION 3
Identify the correct procedure for starting up a PowerBook in Target Disk Mode.
A. Press the D key during startup.
B. Press the T key during startup.
C. Press the Control and D keys during startup.
D. Press the Control and T keys during startup.
E. Press the Command and D keys during startup.
F. Press the Command and T keys during startup.
Correct Answer: B
QUESTION 4
Which THREE of the following features are available in the Aluminum PowerBook G4 models but not in the iBook G4 models?
A. USB ports
B. Audio Input
C. PCMCIA slot
D. Built-in modem
E. Built-in Ethernet
F. FireWire 800 port
Correct Answer: BCF

QUESTION 5
What function does Target Disk Mode perform?
A. It enables direct connectivity with a remote Macintosh over the Internet.
B. It converts a PC-formatted hard disk for use when connected to a Macintosh.
C. It allows access to a Macintosh’s internal hard disk from the Finder of a connected Macintosh via FireWire.
D. It allows two external FireWire hard disks to be connected and transfer data directly between them without need of a computer.
Correct Answer: C
QUESTION 6
Which of the following iBook or PowerBook models requires the use of the 65 watt AC power adapter?
A. iBook (14-inch)
B. iBook G4 (Early 2004)
C. PowerBook G4 (12-inch)
D. PowerBook G4 (1 GHz/867 MHz)
Correct Answer: D
QUESTION 7
Which of the following iBook or PowerBook models requires the use of the 65 watt AC power adapter?
A. iBook G4
B. iBook G4 (14-inch)
C. PowerBook G4 (DVI)
D. PowerBook G4 (15-inch FW800)
Correct Answer: D
QUESTION 8
Which TWO of the following features are available in the Aluminum PowerBook G4 models but not in the Titanium PowerBook G4 models?
A. USB ports
B. PCMCIA slot
C. Built-in modem
D. FireWire 800 port
E. Built-in Bluetooth
F. Built-in wireless networking
Correct Answer: DE
QUESTION 9
The basis for the component isolation troubleshooting technique is an understanding of _______ within computers.
A. power flow
B. software data flow
C. firmware data flow
D. processor instruction flow
Correct Answer: A
QUESTION 10
When setting up a minimal system using the component isolation technique, you start with only the components necessary to _____.
A. boot the system into Mac OS 9
B. boot the system into Mac OS X
C. boot the system into Open Firmware diagnostics
D. hear a boot chime and/or see a flashing question mark on a display
Correct Answer: D
QUESTION 11
In the component isolation technique, if you do not get a startup chime and/or a flashing question mark, you check the components of the minimal system by _____.
A. visually inspecting them for damage
B. replacing them with known-good parts in any order
C. adding more known-good parts in a specified order
D. replacing them with known-good parts in a specified order
Correct Answer: D

The Apple https://www.pass4itsure.com/9l0-206.html training is a vital way of becoming the best. This certification has helped the candidates to enhance their capabilities by providing a great learning platform to them so that they can polish their skills.

Continue Reading

First-hand Apple 9L0-964 Flydumps PDF Download,Apple 9L0-964 Question Ensure Pass Certification

Latest 9L0-964 Reliable Test Blueprint & 9L0-964 Dumps PDF,First-hand Apple https://www.pass4itsure.com/9l0-964.html  Flydumps PDF Download,Apple 9L0-964 Question Ensure Pass Certification

Exam A QUESTION 1
Which clip would be adjusted if you dragged left?(Select the best answer.)

A. Clip in Track V1
B. Clip in Track V2
C. Clip in Track V3

Correct Answer: B QUESTION 2
What is the result of applying the above to an audio clip?(Select the best answer.)

A. The lowest dB reading for the clip will be -6 dB in the Audio Meters.
B. The average dB reading for the clip will be -6 dB in the Audio Meters.
C. The peak dB reading for the clip will be -6 dB in the Audio Meters.

Correct Answer: C
QUESTION 3
Where are Voice Over tool recordings saved?(Select the best answer.)
A. Audio Renders
B. Autosave Vault
C. Capture Scratch
D. Render Files

Correct Answer: C

Continue Reading

Download Latest Dumps for Apple 9L0-611 With Best Quality Study Guide Guarantee You 100% Pass Download

Latest 9L0-611 Apple Real Exam Questions,Download Latest Dumps for https://www.Pass4itsure.com Apple 9L0-611 With Best Quality Study Guide Guarantee You 100% Pass Download

Exam A
QUESTION 1
When a Mac OS X client connects to a server for the first time in a Mac OS X Server v10.4 Open Directory replication system, the client FIRST ________.
A. registers itself with each of the replicas
B. adds a search path for Directory Access for one of the servers in the replication system
C. downloads a list of LDAP replicas from the LDAP server for storage in its LDAPv3 Plugin plist file
D. looks at the Password Server public key and references this key to find out what password servers can be used for authentication

Correct Answer: C QUESTION 2
Which three (3) are Mac OS X Open Directory plug-ins that can request data from a directory service? (Choose THREE.)
A. SMB
B. LDAPv3
C. Bonjour
D. AppleTalk
E. Active Directory
F. BSD Flat File and NIS

Correct Answer: BEF QUESTION 3
Review the following command:
ldapsearch -LLL -x -H ldap://oneserver.example.com -b dc=example,dc=com objectClass=apple-group)?cn objectClass The last two options in this command, cn and objectClass, specify the ________.
A. LDAP entries to exclude from the results
B. attributes to return in the results
C. search filter
D. search base

Correct Answer: B QUESTION 4
Which is a valid method for optimizing the performance of a server providing Open Directory services?
A. Add memory and increase the BerkeleyDB cache size.
B. Store the Open Directory data and logs on the same disk.
C. Store the Open Directory data and operating system on the same disk partition.
D. Run all services that client computers require on the same server that is providing the Open Directory services.

Correct Answer: A QUESTION 5
What two pieces of information must be specified in the Active Directory plug-in configuration in order for Mac OS X v10.4 to bind to Active Directory via the Active Directory plug-in? (Choose TWO.)
A. Computer ID
B. Ethernet address
C. Active Directory tree
D. Active Directory forest
E. Active Directory domain

Correct Answer: AE
QUESTION 6
To support Mac OS X clients, you deploy a server running directory services on Mac OS X Server v10.4 to supplement the existing Active Directory services. This solution provides ________.
A. a mechanism for mapping Mac OS X schema to Active Directory
B. a mechanism for storing Microsoft Exchange data in Open Directory
C. a means of managing Windows Group Policy objects from Workgroup Manager in Mac OS X
D. a way to store user principals in Active Directory, and delegate Mac-specific management to Mac OS X Server

Correct Answer: D
QUESTION 7
What are three (3) ways to supplement data that is missing from a third-party LDAP server to support Mac OS X clients? (Choose THREE.)
A. Repurpose existing fields in the directory schema.
B. Modify the server’s search path to exclude /NetInfo/root.
C. Create local mappings with static and variable attributes.
D. Remove unused objectClasses from the local directory schema.
E. Enable Option 95 to assure communication with the DHCP server.
F. Modify the schema for the directory on the third-party LDAP server.

Correct Answer: ACF
QUESTION 8
What authentication token does a client present when accessing a kerberized service?
A. the user password
B. a client-generated service ticket
C. a service ticket obtained from the key distribution center (KDC)
D. a ticket-granting ticket (TGT) obtained from the key distribution center (KDC)

Correct Answer: C
QUESTION 9
You want services that are running on Mac OS X Server to accept Kerberos service tickets generated by another server. Which of the following is a valid step to accomplish this in Mac OS X Server v10.4?
A. Enable the Kerberos Open Directory plug-in.
B. Use Server Admin to join the Kerberos realm of the other server.
C. Use NeST to establish a trust relationship with the Kerberos server.
D. Add an /etc/kerberos.conf file to define the correct Kerberos domain and service principal.
Correct Answer: B
QUESTION 10
Which tool uses the DirectoryService process to retrieve directory data?
A. Workgroup Manager
B. NetInfo Manager
C. ldapsearch
D. nicl

Correct Answer: A

Continue Reading

Free Sharing The Latest Flydumps Apple 9L0-611 Free VCE Files With All New Exam Questions

Latest 9L0-611 Real Exam Questions And Answers,Free Sharing The Latest Flydumps Apple https://www.pass4itsure.com/9l0-611.html Free VCE Files With All New Exam Questions

Exam A
QUESTION 1
Which information is included in a ticket-granting ticket (TGT) from the key distribution center (KDC)?
A. the public key for the KDC
B. the time the TGT was issued
C. the user account’s crypt password
D. the service key for all supported kerberized services

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Which three are Mac OS X Open Directory plug-ins that can request data from a directory service?
A. SMB
B. LDAPv3
C. Bonjour
D. AppleTalk
E. Active Directory
F. BSD Flat File and NIS

Correct Answer: BEF Section: (none)Explanation
Explanation/Reference:
QUESTION 3
Which is a valid concern when using the Archive feature in Open Directory services on Mac OS X Server v10.4?
A. The archive does not include the local NetInfo database or configuration file
B. The archive contains all of the account passwords and should not be left unsecured
C. You cannot archive a copy of the Open Directory data while the Open Directory master is in service
D. Kerberos must be reconfigured after restoring from an archive, because the archive does not include Kerberos data.

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 4
You are promoting Open Directory services on a computer running Mac OS X Server v10.4 from Standalone Server to Open Directory Master.Which statement about the administrator account is true?
A. The primary administrator account in the local NetInfo database is copied to the LDAP database and used as the primary administrator account for the LDAP database.
B. A new administrator account with the name “diradmin” is created in the LDAP database and assigned the password from the root accont in the local NetInfo database.
C. The root account in the local NetInfo database is copied to the LDAP database and used as the primary administrator account for the LDAP database.
D. A new administrator account is created in the LDAP database, and you assin it a name and password

Correct Answer: C Section: (none)Explanation
Explanation/Reference:
QUESTION 5
You have configured Mac OS X client computers to retrieve user account information from an Active Directory server, and additional directory data from a Mac OS X Server.
Which is a valid concern for this configuration?
A. A modification to the Active Directory schema is necessary
B. The ability to manage individual user accounts in Mac OS X is sacrificed.
C. A Mac OS X computer cannot access two directory servers simultaneously
D. A configured directory on Mac OS X Server must be added to the Active Directory domain

Correct Answer: B Section: (none)Explanation
Explanation/Reference:
QUESTION 6
Review the following command then complete the statement below:
Id apsearch -LLL -x -H Idap://oneserver.example.com -b dc=example, dc=com
“(objectClass=apple-group)” cn objectClass
The last two options in this command, cn and objectClass, specify the _____

A. LDAP entries to exclude from the results
B. Attributes to return in the results
C. Search filter
D. Search base

Correct Answer: B Section: (none)Explanation
Explanation/Reference:
QUESTION 7
What file on a Mac OS X computer is used to specify the location of the key distribution center (KDC) and the Kerberos realm?
A. /Library/Preferences/edu.mit Kerberos
B. ~/Library/Preferences/Kerberos.plist
C. /etc/Kerberos/Kerberos.cof
D. /etc/krb.conf
Correct Answer: A Section: (none) Explanation

Explanation/Reference:
QUESTION 8
You are troubleshooting an Open Directory LDAP server. Which step will allow you to gather troubleshooting information from the server?
A. Start a lapd with the flag -d 99.
B. Turn on verbose logging in Server Admin
C. Start directoryServices with the flag – debug
D: Edit/etc/hostconsig. To contain LDAPARGS=;d;

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 9
In an Open Directory user record, what value should the NFSHome Directory attribute contain?
A. the local file system path to the user’s home folder
B. the IP address of the NFS server providing network home folder
C. the URL used to mount the share point containing the user’s home folder
D. the ID for the mount record that mounts the share point providing the user’s home folder

Correct Answer: A Section: (none)Explanation
Explanation/Reference:
QUESTION 10
When you set up Mac OS X Server to work with a Kerberos key distribution center (KDC), which file is highly sensitive and should be readable only by root?
A. edu.mit.Kerberos.plist
B. Kerberos.conf
C. Krb5.keytab
D. Key.pem

Correct Answer: C

read more: https://www.pass4itsure.com/9l0-611.html

Continue Reading

Professional Apple 9L0-207 Exam Study Guide From Flydumps For Free Download

Pass Apple Certification – Free VCE Apple Exam Questions,Professional Apple https://www.pass4itsure.com/9l0-207.html Exam Study Guide From Flydumps For Free Download

Exam A
QUESTION 1
What tool does the service manual recommend you use to separate plastics and lift components of PowerBook and iBook computers?
A. Nylon probe tool
B. Jeweler screwdriver
C. Flatblade screwdriver
D. Precision needle nose pliers
Correct Answer: A
QUESTION 2
Which TWO of the following are true statements about screws inside a PowerBook or iBook?
A. All screws are interchangeable.
B. It is not necessary to replace all screws after a repair.
C. Screws should always be only comfortably tightened.
D. Screws should always be tightened as much as possible.
E. Screws should always be replaced exactly where they came from.
F. Torx and Hex (Allen) screws can both be driven by either type of driver.
Correct Answer: CE
QUESTION 3
Identify the correct procedure for starting up a PowerBook in Target Disk Mode.
A. Press the D key during startup.
B. Press the T key during startup.
C. Press the Control and D keys during startup.
D. Press the Control and T keys during startup.
E. Press the Command and D keys during startup.
F. Press the Command and T keys during startup.
Correct Answer: B
QUESTION 4
Which THREE of the following features are available in the Aluminum PowerBook G4 models but not in the iBook G4 models?
A. USB ports
B. Audio Input
C. PCMCIA slot
D. Built-in modem
E. Built-in Ethernet
F. FireWire 800 port
Correct Answer: BCF

QUESTION 5
What function does Target Disk Mode perform?
A. It enables direct connectivity with a remote Macintosh over the Internet.
B. It converts a PC-formatted hard disk for use when connected to a Macintosh.
C. It allows access to a Macintosh’s internal hard disk from the Finder of a connected Macintosh via FireWire.
D. It allows two external FireWire hard disks to be connected and transfer data directly between them without need of a computer.
Correct Answer: C
QUESTION 6
Which of the following iBook or PowerBook models requires the use of the 65 watt AC power adapter?
A. iBook (14-inch)
B. iBook G4 (Early 2004)
C. PowerBook G4 (12-inch)
D. PowerBook G4 (1 GHz/867 MHz)
Correct Answer: D
QUESTION 7
Which of the following iBook or PowerBook models requires the use of the 65 watt AC power adapter?
A. iBook G4
B. iBook G4 (14-inch)
C. PowerBook G4 (DVI)
D. PowerBook G4 (15-inch FW800)
Correct Answer: D
QUESTION 8
Which TWO of the following features are available in the Aluminum PowerBook G4 models but not in the Titanium PowerBook G4 models?
A. USB ports
B. PCMCIA slot
C. Built-in modem
D. FireWire 800 port
E. Built-in Bluetooth
F. Built-in wireless networking
Correct Answer: DE
QUESTION 9
The basis for the component isolation troubleshooting technique is an understanding of _______ within computers.
A. power flow
B. software data flow
C. firmware data flow
D. processor instruction flow
Correct Answer: A
QUESTION 10
When setting up a minimal system using the component isolation technique, you start with only the components necessary to _____.
A. boot the system into Mac OS 9
B. boot the system into Mac OS X
C. boot the system into Open Firmware diagnostics
D. hear a boot chime and/or see a flashing question mark on a display
Correct Answer: D

read more: https://www.pass4itsure.com/9l0-207.html

Continue Reading

Recent Updated New Apple 9L0-510 Dumps Download with Exam Practice Questions From Flydumps

Latest 9L0-510 – Apple Real Exam Questions – 100% Free,Recent Updated New Apple https://www.pass4itsure.com/9l0-510.html Dumps Download with Exam Practice Questions From Flydumps

Exam A QUESTION 1
Review the screenshot of the Permissions pane in Server Admin, and then answer the question below.

You have assigned permissions to a folder, as illustrated. What access does the user, Pat, have to the folder?
A. Pat has read-only access to the folder.
B. Pat has write-only access to the folder.
C. Pat does not have any access to the folder.
D. Pat has both read and write access to the folder.

Correct Answer: D QUESTION 2
In Mac OS X Server, preference manifests allow Workgroup Manager to ________.
A. store a common set of preferences in a directory
B. read related blocks of managed preferences at user login
C. associate preferences to a computer using a specific IP address
D. manage preferences for applications that are not already managed by default by Workgroup Manager
Correct Answer: D QUESTION 3
Which utility should you use to manage preferences assigned to computer accounts?
A. Server Admin
B. Directory Utility
C. Server Preferences
D. Workgroup Manager
Correct Answer: D QUESTION 4
Which feature is available in the Software Update service in Mac OS X Server?
A. Restrict client computers to downloading Apple software updates from your software update server only.
B. Automatically download all Apple software updates, but serve only selected updates to client computers.
C. Restrict client computers’ access to Apple software updates based on client computer Ethernet addresses.
D. Create and distribute custom software update packages to client computers, alongside Apple software updates.
Correct Answer: B QUESTION 5
Which statement best describes a mobile user account?
A. A user account created by Setup Assistant on a portable computer.
B. An account that users can log in to only from a computer on a wireless network.
C. An account that users can log in to from either a Mac OS X or a Windows computer.
D. A user account that has been migrated from an Active Directory server to an Open Directory server.
E. A network user account that is copied to the local directory node of the computer when the user logs in.
Correct Answer: E QUESTION 6
You have installed Mac OS X Server v10.6, and are performing its initial configuration. If you select “Create Users and Groups” in the “Users and Groups” pane in Server Assistant, what is the result?
A. The new server is configured as an Open Directory master.
B. The new server is configured as an Open Directory replica.
C. The new server is configured as a standalone directory server.
D. The new server is bound to an existing directory server on the network.
Correct Answer: A QUESTION 7
You want a Mac OS X Server v10.6 computer to use an XML configuration file to configure itself when it starts up for the first time. Which is a valid location to store the configuration file?
A. In /Users/Shared/Auto-Config/ on your DHCP server
B. In /Volumes/usbdrive/Auto Server Setup/ on the new server
C. On any Software Update server on the same subnet as the new server
D. In /Users/Shared/Auto Server Setup/ on any Mac OS X server on your network

Correct Answer: B QUESTION 8
You want to install and configure Mac OS X Server v10.6 on a computer that has been added to your network. Which steps can you take so the computer will automatically configure itself when it restarts after the installation?
A. Save the configuration details as a text file named generic. list, and store the file at the root of the computer’s hard drive.
B. Save the configuration details as a file named setup. list, and store the file in a folder named Auto Server Setup on the root of the computer’s hard drive.
C. Save the configuration details as a record in a directory service running on your network, with the MAC address of the computer as the name of the record.
D. Save the configuration details as a text file, with the computer’s host name as the name of the file, and store the file on any Mac OS X file server on the same subnet as your computer.
Correct Answer: B QUESTION 9
You have performed a default installation of Mac OS X Server on a new computer. Which statement is true of the root account on the computer?
A. You can log in as root and use the Finder.
B. You cannot log in remotely using the root account.
C. You must enable the root account in Directory Utility before you can use it.
D. When logged in as root, you cannot access files in the Documents folders in users’ home folders.
Correct Answer: A QUESTION 10
You have just completed the initial configuration of Mac OS X Server using Server Assistant. The password for the root account is ________.
A. root
B. 12345678
C. the same as the administrator password
D. the first 8 characters of the computer’s hardware serial number
Correct Answer: C

read more: https://www.pass4itsure.com/9l0-510.html

Continue Reading